Heritage and workwear boots with eyelets of 5 mm inner diameter or more suit the 6 mm flat lace F6-XR. It has more volume because more yarn is braided into it, and it looks rustic.
Its strong braid pattern suits sturdy leather and a striking sole. On high-top sneakers and boots in workwear style, the F6-CS looks just as good; it is finer and looks refined. Lace-up ankle boots with eyelets and hooks take the 4 mm flat lace or the 3 mm round lace; that is a matter of taste.
| Lace | Effect | Boots | Lengths |
|---|---|---|---|
| F6-XR | Strong strands, rustic. | Moc-toe boots, heritage and workwear boots. | 75–150 cm |
| F6-CS | Fine braid pattern, refined. | Boots in workwear style, high-top sneakers. | 75–150 cm |
| F4-CS | Slim, subtle sheen. | Lace-up ankle boots with eyelets and hooks. | 60–120 cm |
| R3-CS | Strong round cord. | Lace-up ankle boots and boots with hooks. | 45–150 cm |
For work boots with visible eyelets and hooks, the 6 mm flat lace F6-XR is the best choice. Waxed cotton is tear-resistant and long-lasting.
The flat lace looks stronger on boots; if you have mastered laying it into the hooks, you will happily choose the flat one. That is a matter of taste. In any case, the lace must suit the eyelet.
Waxed shoelaces made of 100 % cotton are water-repellent and keep their shape even when wet. Tightly braided, they do not stretch out.
The wax penetrates the fibre structure of the cotton braid, much like tanning agents penetrate leather. That is why the lace is also dirt-resistant. When wet, the bow does not come undone as easily.
| Situation | What happens |
|---|---|
| Rain Water-repellent | The wax in the braid keeps water out. |
| Soaked Shape | The lace keeps its shape and does not stretch out. |
| Bow When wet | Does not come undone as easily. |
| Become dull Care | Close a cloth with a little shoe cream firmly around the lace and pull it along firmly. |
| For boots Lace | F6-XR (eyelets of 5 mm inner diameter or more) R3-CS (eyelets of 4 mm inner diameter or more) |
You lay the lace into the hook: cross first, then lay it in under tension. If you pull it tight in the channel of the hook, it chafes quickly.
Pulling in the wrong direction is the most common cause of early wear on hooks. Hooks or eyelets often have sharp burrs. If a lace wears through early, deburr the hooks and eyelets once.
| Step | What to do |
|---|---|
| Crossing Before each hook | Cross first, then lead to the hook. |
| Laying in Under tension | Lay in under tension, do not pull tight through the channel. |
| Chafes quickly Burrs | Deburr hooks and eyelets once. |
| Flat laces Twisted | Before laying in, check that the lace lies flat. Once pulled tight while twisted, the twist is hard to correct. |
| Less vulnerable Round laces | R3-CS |
The safest way is to measure your old laces unlaced, from tip to tip. Ankle-high boots usually take 120 cm, tall lace-up boots 150 cm.
Thicker laces need a little more length than thin ones. On boots the eyelets are far apart, so a rule of thumb based on pairs of eyelets helps little here. The R3-CS comes in lengths from 45 to 150 cm, the F4-CS up to 120 cm, the F6-CS and the F6-XR up to 150 cm.
| Length | Typical boots | Lace |
|---|---|---|
| 90 cm Low | Chukkas and low boots. | F4-CS · R3-CS |
| 120 cm Ankle-high | Lace-up ankle boots, ankle-high boots, moc-toe boots. | F6-XR (eyelets of 5 mm inner diameter or more) R3-CS (eyelets of 4 mm inner diameter or more) |
| 150 cm High shaft | Tall lace-up boots, workwear boots. | F6-CS · F6-XR |
| 150 cm Round | Tall lace-up boots with hooks. | R3-CS |
More on our Shoelace length page.
Boots & Outdoor
LACCICO boot & outdoor laces – shape-retaining resilience for boots and lace-up boots
Strong leather boots, heritage boots and lace-up boots place high demands on tensile strength and abrasion resistance. Our waxed shoelaces made of 100 % pure cotton are water-repellent and dirt-resistant. They keep their shape even when wet, and the bow does not come undone so easily.
F6-XR
































F6-CS














































Flat laces 4 mm






















Round laces 3 mm
































Last seen
The right version for heritage boots, lace-up boots and speed hooks
With robust footwear, the type of eyelet and the shaft height decide the ideal shape: while open lacing hooks call for a shape-retaining cord that is not squashed when hooked in, visible eyelets of 5 mm inner diameter or more suit a strong, wide lace. Sharp burrs on eyelets or hooks are best deburred once.
Round laces 3 mm (R3-CS series)
For lacing hooks (speed hooks), chukkas and lace-up boots
The 3 mm round lace is the classic choice for ankle-high leather boots and sporty low shoes. The round cord is less vulnerable on hooks because it cannot twist. The waxing makes it water-repellent and dirt-resistant.
Flat laces 6 mm (F6-XR series | XTRA Robust)
For rugged heritage boots, workwear and sharp-edged metal eyelets
The F6-XR series with its strong strands is made for moc-toe boots and heavy work boots. Made of pure cotton, the lace offers a soft yet solid feel: it has more volume because more yarn is braided into it.




































































































